13436
Electric inflator
Automatic electric compressor, to inflate pneumatic boats and fenders. Pressure control maximum 300 mbar. Output 200 l/min. Operates on 12 Volt battery. Power consumption 9 Amps.
Supplied complete with nozzle fittings and clips to connect to battery.

Manual air pumps



37779
Double chamber foot pump
Double chamber foot pump which delivers a pressure up to 800mBar.
Ideal for boats with inflatable floor.
Capacity : 6 L



5 liter capacity: 16270
6liter capacity: 10157

Foot pump
Heavy duty foot pump particularly suitable for synthetic or rubber coated fabric boats.



Single action, 180 liter/min: 14301
Double action, 300 liter/min: 10386

Stirrup pump
Stirrup type pump which will take the backache out of inflating fenders and inflatable dinghies. Constructed totally of plastic materials for rust free, low maintenance, this pump comes complete with hose and nozzle fittings.

Electrical air pumps
Diaphragm pumps
Diaphragm bilge pumps belong to the Plastimo "classic" products : for almost 40 years, they have been designed and produced in our Lorient-France factory.
In cooperation with the largest boatbuilders, we have improved our pumps over the years so that they can always be perfectly adapted to new boats.
Today, we are very proud to have had our pump selected as standard fitting by the most prestigious European boatbuilders.
Corrosion, electrolysis and fuel resistant bilge pumps. Of rugged construction, they produce high capacity output with the convenience of many mounting positions (see drawings).

· Self-priming and leak free.
· Quick release inspection cover for added safety.

The double action pump is equipped with outlet elbows, swivelling on 220°, thus allowing all mounting positions and reducing the clearance required (290 mm to 400 mm maximum). The outlet elbows are screwed and fitted with an O-ring for perfect watertightness and added safety (quick release facility).
Straight outlets 17491 and elbows 17492 can also be mounted on pump C, which alllows pumping in two different locations on the boat, while having only one waste water outlet.
Model
A
Single Action
B
Single Action
C
Double Action
Ref
11723
11722
11724
Kit of 2 straight oulets
Kit of 2 outlet elbows
Built-in
oulets
17491
17492
Outlets supplied
with pump
Parts common to the 3 pumps
Watertight gasket with cover
Cover alone
Spare handle, length 15.6"
Hose Ø 1 1/2"
Handle stowage clips
Screw cap for back part pump
14263
12611
14315
16216
16702
18040
Model
A
Single Action
B
Single Action
C
Double Action
Ref
11723
11722
11724
Weight
2.2lb
2.2lb
4lb
Capacity output
0.22gal / stroke
0.34gal / stroke
Maximum lift
9.8'
Dimensions
7.6" x 11.6" x 6" depth
7.6" x (11.6" mini - 16" maxi) x 8.4" depth
Hose diameter
Ø 1 1/2"
Pump Model
Pump 925
Pump 1038
Reference
39539
39541
Capacity
0.23gal per cycle
0.25gal per cycle
Capacity
10gal per minute
12gal per minute
Dimensions
7" x 9" x 14.6" (175x225x364mm)
Weight
2lb
2lb
Hose diameter
Ø 1"
Ø 1 1/2"
Accessories
Inlet valve
Outlet valve
40676
40677
2 fastening clips
40678
2 elbow fittings (inlet+outlet)
+ "O" rings
40679
40680
Spare diaphragm
40681
Spare cover
40682
40683

OPTIMUM SAFETY
· No hassle looking for the handle at the critical moment : the Plastimo bilge pump is always ready-to-pump, thanks to its fully integrated handle.
· In case the diaphragm would leak, the water is rejected in the cockpit (not in the bilge), so you can't help noticing it immediately.

SIMPLE INSTALLATION AND MAINTENANCE
· Installing the pump is extremely simple : all done from the cockpit.
· The diaphragm can be removed within seconds, with 3 screws only ; no need to take down the whole pump. This facilitates the cleaning of the pump body (remove small stones and other possible objects clogged in the pump) and enables the replacement of the diaphragm if necessary.
· Construction from materials impervious to UV-rays, resistant to shocks and weathering.

COMPACT
· The Plastimo pump is very compact and the 90° position of the outlets allows installation where space is limited or access difficult.
· Outlets swivel through 360° and therefore adapt perfectly to the pump position in relation to the strainer and thru-hull fitting.

DESIGN
· One obviously expects from a pump that it should first and foremost be efficient… In addition to the remarkable technical performance, Plastimo has paid a particular attention to design and aesthetics, building on years of expertise in composite materials and plastic engineering. The result is a stylishly designed pump, which matches very nicely the cockpit of modern boats.


© Plastimo USA 2005. All rights reserved. Copying without permission is expressly forbidden.
Home > Products > Plumbing > Pumps

 

 

 

 

 

 

 

Manual bilge pump

 

 

 

Home   |   About Us    |   News   |   Products  |   Contact Us  |   Dealers

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Emergency diaphragm pump

12760
Plastimo’s multiposition manual diaphragm bilge pump can be installed in any one of eight horizontal or vertical positions. Rugged, durable pump is molded of impact- and chemical-resistant plastic and stainless steel. Diaphragm removes easily. Includes two 1” (25mm) outlets. Hose not included.

Technical specifications:

Hand pump

Self-priming manual pump can be used in any position. Low-maintenance all-plastic construction. 1” (25mm) hose (not included) can be attached to the outlet. Also available with 3.3’ (1m) hose.

Pump alone
Pump + 3.3' hose
Output per stroke
Min. dimensions
Stroke
14089
14105
14090
27074
27075
27076
0.13gal
0.20gal
0.26gal
19.2"
25.2"
31.6"
13.2"
19.2"
25.6"
Accessories:

82' hose Ø 1"...................16209
Stowage clips Ø 2"...........16707